NF Best Camper Rooftop Air Conditioner Caravan RV Top Air Conditioner
Product Description
This parking air conditioner fast cooling, stable operation, virtually silent and energy efficient.
The operational efficiency of the air conditioner is influenced by both internal and external environmental conditions within the recreational vehicle (RV). Minimizing heat gain inside the RV can significantly enhance the performance and energy efficiency of the air conditioning system. The following recommendations can help reduce heat accumulation in your RV:
1. Park the RV in a shaded area to minimize solar heat gain.
2. Keep windows closed and use blinds or curtains to block direct sunlight.
3. Ensure doors remain closed when not in use to prevent warm air from entering.
4. Limit the use of heat-generating appliances to reduce internal heat load.
Initiating the cooling or heating process early in the day can significantly enhance the heat pump’s effectiveness in maintaining the desired indoor temperature. In environments characterized by high temperature and humidity, it is recommended to operate the air conditioner in Cool mode with the fan speed set to High. This configuration promotes optimal cooling performance and system efficiency.
The advantages of this caravan rooftop air conditioner:
low-profile & modish design, pretty stable operation, super quiet, more comfortable, lower consumed power.
Technical Parameter
RT2-135：
For 220V/50Hz,60Hz version, rated Heat Pump Capacity: 12500BTU or optional Heater 2000W.
For 115V/60Hz version, optional Heater 1400W only.
RT2-150：
For 220V/50Hz,60Hz version, rated Heat Pump Capacity: 14500BTU or optional Heater 2000W.
For 115V/60Hz version, optional Heater 1400W only.
| Model |
NFRT2-135 |
NFRT2-150 |
| Rated Cooling Capacity |
12000BTU |
14000BTU |
| Power Supply |
220-240V/50Hz, 220V/60Hz, 115V/60Hz |
220-240V/50Hz, 220V/60Hz,115V/60Hz |
| Refrigerant |
R410A |
|
| Compressor |
vertical rotary type, LG or Rechi |
|
| System |
One motor + 2 fans |
|
| Inner frame material |
EPS |
|
| Upper Unit Sizes |
890*760*335 mm |
890*760*335 mm |
| Net Weight |
39KG |
41KG |
Indoor Panels
Indoor Control Panel ACDB
Mechanical rotary knob control, fitting non ducted installation.
Control of cooling and heater only.
Sizes (L*W*D):539.2*571.5*63.5 mm
Net Weight: 4KG
Indoor Control Panel ACRG15
Electric Control with a Wall-pad controller, fitting both ducted and non ducted installation.
Multi control of cooling, heater, heat pump and the separate Stove.
With Fast Cooling function via opening the ceiling vent.
Sizes (L*W*D):508*508*44.4 mm
Net Weight: 3.6KG
Indoor Control Panel ACRG16
Newest launch, popular choice.
Remote controller and Wifi(Mobile Phone Control) control, multi control of A/C and the separate stove.
More humanized functions like a household air conditioner, cooling, dehumidification, heat pump, fan, automatic, time on/off, ceiling atmosphere lamp(multicolor LED strip) optional, etc.
Sizes(L*W*D):540*490*72 mm
Net Weight: 4.0KG
Installation & Application
INSTALLATION INSTRUCTIONS
1. PRECAUTIONS
A. Carefully read all installation and operation instructions before beginning the installation of your air conditioner or heat pump.
B. The manufacturer assumes no liability for any damage or injury resulting from failure to follow these instructions.
C. Installation must conform to the National Electrical Code, as well as any applicable state or local codes and regulations.
D. DO NOT install or use any additional devices or accessories with this air conditioner or heat pump unless explicitly approved by the manufacturer.
E. This equipment must be serviced exclusively by qualified personnel; in certain jurisdictions, licensed technicians are required.
2. SELECTING AN INSTALLATION LOCATION FOR THE AIR CONDITIONER / HEAT PUMP
This product is specifically designed for installation as a rooftop air conditioner or heat pump unit on recreational vehicles (RVs). Any use outside of this intended application will void the manufacturer’s warranty.
A. STANDARD INSTALLATION LOCATIONS
The unit is designed to be installed over an existing roof vent opening. Upon removal of the vent, a standard opening of approximately 14-1/4" x 14-1/4" with a tolerance of ±1/8" is typically created.
B. ALTERNATIVE INSTALLATION LOCATIONS
If a roof vent is not available or an alternate installation location is preferred, the following guidelines are recommended:
FAQ
Q1. What is your terms of packing?
A: Generally, we pack our goods in neutral white boxes and brown cartons. If you have legally registered patent, we can pack the goods in your branded boxes after getting your authorization letters.
Q2. What is your terms of payment?
A: T/T 100% in advance.
Q3. What is your terms of delivery?
A: EXW, FOB, CFR, CIF, DDU.
Q4. How about your delivery time?
A: Generally, it will take 30 to 60 days after receiving your advance payment. The specific delivery time depends on the items and the quantity of your order.
Q5. Can you produce according to the samples?
A: Yes, we can produce by your samples or technical drawings. We can build the molds and fixtures.
Q6. What is your sample policy?
A: We can supply the sample if we have ready parts in stock, but the customers have to pay the sample cost and the courier cost.
Q7. Do you test all your goods before delivery?
A: Yes, we have 100% test before delivery.
Q8: How do you make our business long-term and good relationship?
A:1. We keep good quality and competitive price to ensure our customers benefit;
2. We respect every customer as our friend and we sincerely do business and make friends with them, no matter where they come from.
